Skip to content
Krevo
KREVO Inject PU-Foam
Injection System

KREVO Inject PU-Foam

Water-reactive two-component polyurethane injection foam · Rapid stopping of active leaks

Type
PU Injection Temporary
Pack sizes
5.5 L combined (approximately 6.15 kg)
Shelf life
12 months in unopened dry containers at approximately +25 °C
Technical data sheet

Overview

KREVO Inject PU-Foam is a low-viscosity, solvent-free, two-component polyurethane resin system that expands rapidly into a stable foam when it contacts water. It is intended to temporarily stop or reduce active water leakage through concrete cracks and cavities, allowing KREVO Inject PU- Flex permanent flexible sealing resin. Catalyst concentration is selected to control foaming reaction time.

Advantages

  • Rapid water-activated expansion seals flowing cracks and voids.
  • Adjustable catalyst dosage allows reaction speed to suit site conditions.
  • Low-viscosity liquid can be injected through drilled packers.
  • Stable cured foam with adhesion to prepared concrete surfaces.
  • Suitable for experienced injection crews working in varied climates.

Typical uses

  • Emergency water stopping in concrete walls and slabs
  • Leaking construction joints and crack networks
  • Foundations, basements and tunnels
  • Water-retaining and marine concrete structures
  • Preparation for subsequent permanent PU crack sealing (KREVO Inject PU-Flex)

Technical data

Technical properties

Typical values from the technical data sheet. Always confirm with the current data sheet before use.

Full data sheet

Specification

Generic type
Two-component water-reactive polyurethane injection foam
Composition
Solvent-free low-viscosity PU base (Part A) and catalyst (Part B)
Reaction mechanism
Rapid expansion into stable foam on contact with water
Base | Part A
5.0 L (approximately 5.65 kg)
Catalyst | Part B
0.5 L (approximately 0.50 kg)
Appearance / use
Liquid components for injection; expanding water-stop foam
Shelf life / storage
12 months in unopened dry containers at approximately +25 °C
Free foam expansion
≥ 3,000% (at 10% catalyst; +25 °C / 50% RH)
Viscosity
20–40 mPa·s (+25 °C / 50% RH)
Elongation | ASTM D638
15–20%
2% catalyst by volume
Foam starts ~28 s; finishes ~104 s
4% catalyst by volume
Foam starts ~19 s; finishes ~72 s
6% catalyst by volume
Foam starts ~16 s; finishes ~57 s
8% catalyst by volume
Foam starts ~14 s; finishes ~45 s
10% catalyst by volume
Foam starts ~12 s; finishes ~44 s
VOC | reacted foam
< 100 g/L (EPA Method 24 basis)

FAQ

KREVO Inject PU-Foam: questions

What is KREVO Inject PU-Foam?

KREVO Inject PU-Foam is a low-viscosity, solvent-free, two-component polyurethane resin system that expands rapidly into a stable foam when it contacts water. It is intended to temporarily stop or reduce active water leakage through concrete cracks and cavities, allowing KREVO Inject PU- Flex permanent flexible sealing resin. Catalyst concentration is selected to control foaming reaction time.

What is KREVO Inject PU-Foam used for?

KREVO Inject PU-Foam is used for: emergency water stopping in concrete walls and slabs; leaking construction joints and crack networks; foundations, basements and tunnels; water-retaining and marine concrete structures; preparation for subsequent permanent PU crack sealing (KREVO Inject PU-Flex).

What pack sizes is KREVO Inject PU-Foam available in?

KREVO Inject PU-Foam is supplied in 5.5 L combined (approximately 6.15 kg).

What is the shelf life of KREVO Inject PU-Foam?

Shelf life / storage: 12 months in unopened dry containers at approximately +25 °C.

Is there a technical data sheet for KREVO Inject PU-Foam?

Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.

Ask our team

About: KREVO Inject PU-Foam