KREVO Prime EP
High-Penetration, Solvent-free Epoxy Primer · For protective coatings, Flooring and Structural Systems
- Type
- Epoxy Primer
- Pack sizes
- 1 L and 5 L packs; 1 quart and 1 gallon packs for USA
- Coverage
- 10 m²/L at approximately 100 µm WFT
- Shelf life
- 12 months; sealed, dry, shaded, below +30 °C
See it applied
Preparing and priming a floor
How KREVO Prime EP goes on site, step by step.
- 1 Grind the surface
- 2 Vacuum and prime
Illustration of the application process, not footage of a specific project. Follow the technical data sheet for the full method.
Overview
KREVO Prime EP is a two-component, low-viscosity epoxy primer designed to penetrate suitably prepared concrete and promote bonding of compatible epoxy coatings and resin systems. The solvent-free primer helps seal pores and reduce substrate outgassing, creating a sound interface for subsequent protective layers.
Advantages
- Low-viscosity, high-penetration epoxy formulation.
- Solvent-free and low-VOC formulation; formaldehyde-free design.
- Enhances adhesion of compatible coatings and floor toppings.
- Helps seal porous concrete and limit outgassing-related defects.
- Suitable for brush, roller or approved airless-spray application.
Typical uses
- Concrete primer for epoxy floor coatings
- Resin flooring and protective coating systems
- Porous substrate sealing
- Bond-promoting priming of prepared concrete prior to compatible epoxy toppings
Technical data
Technical properties
Typical values from the technical data sheet. Always confirm with the current data sheet before use.
Specification
- Material type
- Two-component epoxy primer (base and hardener)
- Formulation
- Solvent-free, low-viscosity, high-penetration resin
- Principal purpose
- Promotes coating adhesion; seals pores and reduces outgassing
- Substrate
- Structurally sound, prepared concrete; typically ICRI CSP 4–5
- Application method
- Brush, roller or approved airless spray
- Theoretical coverage
- 10 m²/L at approximately 100 µm WFT
- Storage / shelf life
- 12 months; sealed, dry, shaded, below +30 °C
- Volume solids
- 100%
- Specific gravity
- 1.05 ± 0.05
- Pot life / touch dry
- 60 minutes / 3 hours at +30 °C
- Recoat interval / VOC
- 6–24 hours at +30 °C / < 10 g/L
Used together with
Epoxy floor system
KREVO Prime EP is one step of this system, as shown in our application film. Follow each product's data sheet for compatibility and overcoating times.
-
1Primer
KREVO Prime EP
This product
-
2Floor topping or coating
FAQ
KREVO Prime EP: questions
What is KREVO Prime EP?
KREVO Prime EP is a two-component, low-viscosity epoxy primer designed to penetrate suitably prepared concrete and promote bonding of compatible epoxy coatings and resin systems. The solvent-free primer helps seal pores and reduce substrate outgassing, creating a sound interface for subsequent protective layers.
What is KREVO Prime EP used for?
KREVO Prime EP is used for: concrete primer for epoxy floor coatings; resin flooring and protective coating systems; porous substrate sealing; bond-promoting priming of prepared concrete prior to compatible epoxy toppings.
How is KREVO Prime EP applied?
In outline: 1. Grind the surface 2. Vacuum and prime. The video on this page shows the process; always follow the technical data sheet for surface preparation, mixing and application details.
What pack sizes is KREVO Prime EP available in?
KREVO Prime EP is supplied in 1 L and 5 L packs; 1 quart and 1 gallon packs for USA.
What is the coverage of KREVO Prime EP?
Coverage / consumption: 10 m²/L at approximately 100 µm WFT. Actual consumption depends on the substrate and application; see the technical data sheet.
What is the shelf life of KREVO Prime EP?
Shelf life / storage: 12 months; sealed, dry, shaded, below +30 °C.
Is there a technical data sheet for KREVO Prime EP?
Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.
More in Floor Solutions
PU SL
Floor Solutions
KREVO Floor PU-SL
Self-leveling Urethane Hybrid Flooring · Flow-applied floor topping
View product
PU Screed
Floor Solutions
KREVO Floor PU-Screed
Heavy-duty polyurethane-cement floor screed · Hygienic, slip-resistant finish · 6-12 mm
View product
Epoxy SL
Floor Solutions
KREVO Floor EP-SL
Abrasion- and chemical-resistant self-leveling epoxy flooring · Three-component system · 1–4 mm
View product