Skip to content
Krevo
KREVO Inject MicroCem
Injection System

KREVO Inject MicroCem

High performance ultra-fine injection cement · Concrete and geotechnical grouting

Type
Cementitious Injection
Pack sizes
25 kg bags
Shelf life
Dry, shaded conditions, below +25°C
Technical data sheet

Overview

KREVO Inject MicroCem is an ultra-fine blast furnace slag cement system for penetrating fine cracks and voids in concrete, rock and soil. It is intended for specialist injection grouting, ground improvement and upgrading conventional cement grouts and mortars. Two fineness grades, B6 and B10, allow selection to suit the project.

Advantages

  • Very fine particle size and high penetrability in suitable cracks and porous media.
  • Low permeability and good long-term durability after appropriate curing.
  • High resistance to sulfate- and chloride-bearing environments.
  • Mineral-based, non-toxic injection-grouting technology.
  • Choice of B6 and B10 grades to match penetration and grout-mix requirements.

Typical uses

  • Concrete crack injection
  • Soil and rock stabilization
  • Foundation support
  • Sealing of sheet piles
  • Groundwater cut-off and underground stream sealing
  • Performance enhancement of cement-based grouts and mortars

Technical data

Technical properties

Typical values from the technical data sheet. Always confirm with the current data sheet before use.

Full data sheet

Specification

Generic type
Ultra-fine blast furnace slag injection cement
Available grades
B6 (maximum 6 µm) and B10 (maximum 10 µm)
Form
Dry ultra-fine cementitious powder
Principal applications
Concrete crack injection; soil, rock and foundation grouting
Binder performance
High strength after curing; values vary by grade
Storage
Dry, shaded conditions, below +25°C
Shelf life
6 months in unopened, properly stored bags
Maximum grain size
B6: 6 µm | B10: 10 µm
Blaine specific surface
B6: ~1,900 m²/kg | B10: ~1,600 m²/kg
Median particle size, d50
B6: ≤2.5 µm | B10: ≤3.5 µm
Particle size, d95
B6: ≤6 µm | B10: ≤9.5 µm
Compressive strength, 1 day
B6: ≥25 MPa | B10: ≥10 MPa
Compressive strength, 2 days
B6: ≥45 MPa | B10: ≥35 MPa
Compressive strength, 28 days
B6: ≥70 MPa | B10: ≥70 MPa
Reference test basis
Typical dry binder laboratory data
Site effects
Actual results vary with mix and conditions

FAQ

KREVO Inject MicroCem: questions

What is KREVO Inject MicroCem?

KREVO Inject MicroCem is an ultra-fine blast furnace slag cement system for penetrating fine cracks and voids in concrete, rock and soil. It is intended for specialist injection grouting, ground improvement and upgrading conventional cement grouts and mortars. Two fineness grades, B6 and B10, allow selection to suit the project.

What is KREVO Inject MicroCem used for?

KREVO Inject MicroCem is used for: concrete crack injection; soil and rock stabilization; foundation support; sealing of sheet piles; groundwater cut-off and underground stream sealing; performance enhancement of cement-based grouts and mortars.

What pack sizes is KREVO Inject MicroCem available in?

KREVO Inject MicroCem is supplied in 25 kg bags.

What is the shelf life of KREVO Inject MicroCem?

Shelf life / storage: Dry, shaded conditions, below +25°C.

Is there a technical data sheet for KREVO Inject MicroCem?

Yes. The technical data sheet (PDF) can be downloaded from this page. For project-specific advice or a quotation, send an enquiry to the Krevo technical team.

Ask our team

About: KREVO Inject MicroCem